The Story
When your lift build calls for a matched rear to complement your front suspension work, the Britpart DA6345 +50mm (2 in) Rear Spring Spacer Blocks complete the picture. Designed as the direct companion to the DA6344 front pair, these rear blocks install between the axle and the factory spring seats at the rear to deliver a clean and consistent 50mm (2 in) of additional lift height. The result is a balanced, level lift across all four corners when used together with the front pair, making this one of the most straightforward ways to raise your classic Land Rover without committing to a full suspension overhaul.
Each block in this rear pair is fabricated from 6mm (0.24 in) thick steel plate and finished in a durable powder coat that stands up to the mud, water, and general punishment these platforms were designed to endure. Britpart brings their well-established manufacturing standards to this component, backed by their 24-month guarantee and a global distribution network that has made them a go-to name for classic Land Rover owners worldwide.
Installation requires no cutting or welding. The blocks drop into the existing spring seat location at the rear axle, making this an accessible job for anyone comfortable with basic suspension work. As with any suspension height change, a full alignment check after fitting is always a sensible step to confirm that handling and geometry remain within safe specification.
Whether you are building a dedicated off-road setup, adding ground clearance for overlanding, or simply leveling out a tired or sagging rear end, the DA6345 delivers reliable, repeatable lift with minimal complexity.
Fits:
- Defender 90 (1983 to 2016)
- Defender 90 NAS (1993 to 1997)
- Defender 110 (1983 to 2016)
- Defender 110 NAS (1993 to 1997)
- Defender 130 (1984 to 2016)
- Discovery 1 (1989 to 1998)
- Range Rover Classic (1970 to 1996)
Part Number: DA6345
Free shipping to the lower 48!
No supersessions found.
FAQ
Is this the front or rear spacer block pair?
This is the rear pair. If you need the matching front blocks, those are sold separately under part number DA6344. Many owners purchase both sets together to achieve a balanced full-vehicle lift.
What is included in this listing?
This listing includes two rear spring spacer blocks as a matched pair, which is everything needed to complete the rear axle lift on the supported vehicles. No additional spacer hardware is required for the rear installation.
Do I need longer shock absorbers when fitting these spacers?
Adding 50mm (2 in) of lift via spacer blocks does increase the droop travel demand on your shock absorbers. Depending on the condition and spec of your existing dampers, uprated or longer shocks are worth considering to get the full benefit of the lift and maintain proper suspension articulation. A front-end alignment and a check of all suspension geometry is also recommended after any suspension modification.
Description
When your lift build calls for a matched rear to complement your front suspension work, the Britpart DA6345 +50mm (2 in) Rear Spring Spacer Blocks complete the picture. Designed as the direct companion to the DA6344 front pair, these rear blocks install between the axle and the factory spring seats at the rear to deliver a clean and consistent 50mm (2 in) of additional lift height. The result is a balanced, level lift across all four corners when used together with the front pair, making this one of the most straightforward ways to raise your classic Land Rover without committing to a full suspension overhaul.
Each block in this rear pair is fabricated from 6mm (0.24 in) thick steel plate and finished in a durable powder coat that stands up to the mud, water, and general punishment these platforms were designed to endure. Britpart brings their well-established manufacturing standards to this component, backed by their 24-month guarantee and a global distribution network that has made them a go-to name for classic Land Rover owners worldwide.
Installation requires no cutting or welding. The blocks drop into the existing spring seat location at the rear axle, making this an accessible job for anyone comfortable with basic suspension work. As with any suspension height change, a full alignment check after fitting is always a sensible step to confirm that handling and geometry remain within safe specification.
Whether you are building a dedicated off-road setup, adding ground clearance for overlanding, or simply leveling out a tired or sagging rear end, the DA6345 delivers reliable, repeatable lift with minimal complexity.
Fits:
- Defender 90 (1983 to 2016)
- Defender 90 NAS (1993 to 1997)
- Defender 110 (1983 to 2016)
- Defender 110 NAS (1993 to 1997)
- Defender 130 (1984 to 2016)
- Discovery 1 (1989 to 1998)
- Range Rover Classic (1970 to 1996)
Part Number: DA6345
Free shipping to the lower 48!
No supersessions found.
FAQ
Is this the front or rear spacer block pair?
This is the rear pair. If you need the matching front blocks, those are sold separately under part number DA6344. Many owners purchase both sets together to achieve a balanced full-vehicle lift.
What is included in this listing?
This listing includes two rear spring spacer blocks as a matched pair, which is everything needed to complete the rear axle lift on the supported vehicles. No additional spacer hardware is required for the rear installation.
Do I need longer shock absorbers when fitting these spacers?
Adding 50mm (2 in) of lift via spacer blocks does increase the droop travel demand on your shock absorbers. Depending on the condition and spec of your existing dampers, uprated or longer shocks are worth considering to get the full benefit of the lift and maintain proper suspension articulation. A front-end alignment and a check of all suspension geometry is also recommended after any suspension modification.
